Most recent dyno pull, from today!
#1
Registered User
Thread Starter
Join Date: Dec 2003
Location: Los Gatos, CA
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Most recent dyno pull, from today!
Well today my Z went to Scotts Performance to finally be dyno tuned after the most recent modifications. This dyno pull, was done in 5th gear! Even in 5th gear we were still spinning the tires on the dyno. Also, this is a load based dyno ( a dynamometer ) and reads slightly lower then your average DynoJets do. All of Teds neighbors were complaining telling Ted to shut the car off, so on top of being in 5th gear, there is still some fine tuning to happen Ted just told them it was an airplane flying overhead from the airport.
Well, the number came to alot @ 8,000 RPM on alot of Boost with the "stock" APS twins. Again, with some fine tuning, and on a dynojet, I would expect higher numbers.
Not to mention, I have a set of bigger twins sitting in Teds office right now, just waiting to be installed. I'm hoping to hit alot more RWHP then what i have, I don't want to max the new twins out
Just a few pics, fillin up with 100.
Well, the number came to alot @ 8,000 RPM on alot of Boost with the "stock" APS twins. Again, with some fine tuning, and on a dynojet, I would expect higher numbers.
Not to mention, I have a set of bigger twins sitting in Teds office right now, just waiting to be installed. I'm hoping to hit alot more RWHP then what i have, I don't want to max the new twins out
Just a few pics, fillin up with 100.
Last edited by marluci7; 03-20-2006 at 03:21 PM.
#6
Registered User
Join Date: Apr 2005
Location: CALI
Posts: 2,059
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by phunk
The car looks nice.
Please find out what type of dyno and let us know.
Please find out what type of dyno and let us know.
Trending Topics
#11
Registered User
Join Date: Aug 2003
Location: Los Gatos, CA
Posts: 1,981
Likes: 0
Received 0 Likes
on
0 Posts
I'll let Marin answer his engine details...
But yeah still on the unichip, these Z's seem to love them.
Wheels are just 18 inch Nismos, on 295 BF goodrich Drag raidals, Tein flex coilovers and camber kit to straighten the wheels back out some.
As he said today to someone else asking the same question.. If he has a lot of gas, and a passenger, he can floor it in third gear.
I know he has plans for wider wheels/rubber soon!
But yeah still on the unichip, these Z's seem to love them.
Wheels are just 18 inch Nismos, on 295 BF goodrich Drag raidals, Tein flex coilovers and camber kit to straighten the wheels back out some.
As he said today to someone else asking the same question.. If he has a lot of gas, and a passenger, he can floor it in third gear.
I know he has plans for wider wheels/rubber soon!
#18
Registered User
Thread Starter
Join Date: Dec 2003
Location: Los Gatos, CA
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by bigbri
Load based dyno ( a dynamometer ) Dastek dyno....Good **** Marin..Looking forward to getting a ride in the beast tommorow..I'll be there from 12pm on..stop by..give me a ride... I may have the same setup as you soon..we'll see..
#19
General & Tech Senior Moderator
MY350Z.COM
MY350Z.COM
iTrader: (74)
wOw. I remember seeing your car a long while ago. And I feel in love with it. Te-37's Same exterior and you could barely see the Intercooler. Very sleeper. Just what I like. You sir are a pioneer. I can't wait just like the rest for the results with the new snails.
Keep it up and Keep us Proud
O and I think someone asked why you don't post on the board. I wouldn't be posting ethier if I had that beast in my garage. I would be driving it around.
Keep it up and Keep us Proud
O and I think someone asked why you don't post on the board. I wouldn't be posting ethier if I had that beast in my garage. I would be driving it around.
Last edited by NA&CH; 02-24-2006 at 07:53 AM.
#20
Registered User
Thread Starter
Join Date: Dec 2003
Location: Los Gatos, CA
Posts: 175
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Turbogt
wOw. I remember seeing your car a long while ago. And I feel in love with it. Te-37's Same exterior and you could barely see the Intercooler. Very sleeper. Just what I like. You sir are a pioneer. I can't wait just like the rest for the results with the new snails.
Keep it up and Keep us Proud
O and I think someone asked why you don't post on the board. I wouldn't be posting ethier if I had that beast in my garage. I would be driving it around.
Keep it up and Keep us Proud
O and I think someone asked why you don't post on the board. I wouldn't be posting ethier if I had that beast in my garage. I would be driving it around.
Last edited by marluci7; 02-24-2006 at 08:01 AM.